Etanol.nu

Forum för föreningen etanol.nu
Aktuellt datum och tid: tor 24-03-28 23:12

Alla tidsangivelser är UTC + 1 timme




Ny tråd Svara på tråd  [ 62 inlägg ]  Gå till sida Föregående  1, 2, 3, 4, 5  Nästa
Författare Meddelande
 Inläggsrubrik:
InläggPostat: sön 09-11-08 20:09 
Offline
Forumadministratör
Användarvisningsbild

Blev medlem: lör 06-12-23 09:31
Inlägg: 7134
Ort: Älvsjö
I asked one of he Bosch engineers involved in designing the flex start system about the systems coldstart abilities with E85 and the tyoe of glowplugs used and got these answers:

Citat:
Regarding you specific questions:
_ We did some initial studies about the use of the tecnology to start a vehicle at -30 degC. We used a brazilian car, with the same oil, using the brazilian gasoline to prepare the ethanol and we could start a vehicle down to -25 degC. I do believe ther is room for improvement, once as I said it was a basic evaluation of the potential. One critical point here is that the system requires a pre-heating time for the fuel to reach a minimum temperature. This could be minimized by incresing the gasoline content in the fuel misture during winter.

_ Although the heating elements looks like a typical Diesel glow plug, they are not. They are designed to resist the continuous exposition to E100 (93% Ethanol + 7% Water) with no problems and the power in higher.

I had the opportunity to have preliminary discussions about the technology with SAAB, about one year ago.

_________________
Komplettera gärna data om dit piggybacksystem här: http://www.editgrid.com/user/aryan/E85_piggyback_system och här viewtopic.php?f=10&t=6352


Dela på FacebookDela på TwitterDela på TuentiDela på SonicoDela på FriendFeedDela på OrkutDela på DiggDela på MySpaceDela på DeliciousDela på TechnoratiDela på TumblrDela på Google+
Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: sön 09-11-08 20:31 
Offline

Blev medlem: mån 08-09-01 22:07
Inlägg: 300
Ort: Ukraine, Donetsk
as i understood:

1. this is usual glowplug, but with spesial anticorrosion coating or something like that

2. engine can be started with only fuel heating up to -25...-30 C

is it correct?


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: sön 09-11-08 20:53 
Offline
Forumadministratör
Användarvisningsbild

Blev medlem: lör 06-12-23 09:31
Inlägg: 7134
Ort: Älvsjö
Obormot skrev:
as i understood:

1. this is usual glowplug, but with spesial anticorrosion coating or something like that

2. engine can be started with only fuel heating up to -25...-30 C

is it correct?


Yes this is how I understood it too, but I think for -25°C they mixed a E85 from ethanol and gasoline.

With waterfree E85 one does not neet to be concerned about the glowplugs corrosion, I would ot be so worried about that anyway.


/Aryan

.

_________________
Komplettera gärna data om dit piggybacksystem här: http://www.editgrid.com/user/aryan/E85_piggyback_system och här viewtopic.php?f=10&t=6352


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: sön 09-11-08 21:29 
Offline

Blev medlem: mån 08-09-01 22:07
Inlägg: 300
Ort: Ukraine, Donetsk
we using ethanol with 7-8% of water - an i not see any sense to remove it, if we will not use gasoline to mix with ethanol.

additives solving all problems with corrosion - we made tests with copper, aluminium, steel, lead and tin - glass cans with this metals was filled with our fuel and everything is OK.

and there are visible corrosion on metals in cans, filled with pure 92% ethanol.


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: sön 09-11-08 21:33 
Offline

Blev medlem: tis 08-08-19 15:54
Inlägg: 503
Ort: Umeå, Västerbotten
this is OT but where do you find 92% ethanol.

_________________
Saab 900 2.0t -97 E85 mappad+Steg 1
Volvo 850 Flextek


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: sön 09-11-08 22:50 
Offline
Forumadministratör
Användarvisningsbild

Blev medlem: lör 06-12-23 09:31
Inlägg: 7134
Ort: Älvsjö
Brasil & Ukraine :-)

I wish we could get it here too.

/Aryan

_________________
Komplettera gärna data om dit piggybacksystem här: http://www.editgrid.com/user/aryan/E85_piggyback_system och här viewtopic.php?f=10&t=6352


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: lör 09-11-14 00:45 
Offline
Forumadministratör
Användarvisningsbild

Blev medlem: lör 06-12-23 09:31
Inlägg: 7134
Ort: Älvsjö
This is what the Brasilian flexstart engineer tells me about their tests:

Citat:
aryan skrev:
- Did I understand correctly that you could start at -25°C with a mixture of 15% Brazilian gasoline and 85% anhydrous (waterfree) ethanol if you waited long enough for the flex start system o heat the fuelrail or was it with even less (no?) gasoline in the fuel?


_ We were able to start a vehicle @ -25°C using a mixture of 15% Brazilian Gasoline + 85 Hidrated Ethanol (~ 7% water).


Not bad with the 7% water!

Citat:
aryan skrev:
- Are the heating plugs that you use internally temperature controlled like a PTC so that they are preset for a temperature of for example 100°C or does the electronic controle system control the temperature of the plugs?


_ The heating elements have a PTC feature in the sense their resistance increases with temperature but they are not like typical ceramic PTCs in which the temperature is pre-detrmined by the composition of the ceramic.


So they are probably using current controlled fast glowplugs, like I suspected.

Citat:
aryan skrev:
- Would it not be an even better solution to start with electric heated fuel and than hose a heat exhanger before the fuel rail to continue to heat the fuel with the cooling liquid once the engine gets warm? If that can help to evapourate the fuel more completely before ignition, both fuel consumption and also HC and CO emissions should become lower, but may be NOx would get higher?


_ Regarding your idea of using the heat generated by the engine to sustain the fuel heating, it is a nice idea.
Indeed we have evaluated it. The concern is that we basically need to heat up the fuel only for the engine to start and
during the warm-up phase because once the water temperature increases to a minimum value the engine reachs a good
burning efficiency and you do not need to keep heating the fuel. Basically 90% of the emission occurs in the first 90s of
operation. Another issue is the control of the fuel temperature in all opetaing condition which is not cheap.
Normally when HC is reduced the NOx increases, but this can be compensated by re-adjusting the catalyst converter operating window.

_________________
Komplettera gärna data om dit piggybacksystem här: http://www.editgrid.com/user/aryan/E85_piggyback_system och här viewtopic.php?f=10&t=6352


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: fre 09-12-25 17:03 
Offline
Forummoderator

Blev medlem: mån 07-01-01 20:57
Inlägg: 6015
Ort: Hindås
Obormot skrev:
now temperature is about 0 ... -2 C, gasoline in ethanol is 2-3%, engine with 3-4 min of fuelrail preheating starts pretty good - in 2-3 second of cranking.

i try to turn off heating when driving - difference is big, driveability decreases, fuel consumption in city mode increases, about 0.8 l/100 km.

middle of fuelrail is hot, but the ends are just warm - i think if heating will be more uniform it will work much better.

power consumption of heaters on hot engine is about 20-30 W.


This shows that Bosch engineer are not telling all the truth, also during running with warm engine it is beneficial to heat the fuel.
But Bosch saw a too high price for such a system and choosed to not include a coolant heat exchanger before the heated fuel rail.
Economics ruined a good idea, again...

_________________
http://direktdemokraterna.se
Myndigförklara dig själv.


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: fre 10-01-22 16:22 
Offline

Blev medlem: fre 08-05-16 11:27
Inlägg: 84
Ort: Linköping
Powerful but unfortunately too hot, I'm afraid:

http://www.conrad.se/?article=532894

I have not found suitable PTC elements for sale in Sweden. Anyone else?

Resistance wire would be simple to apply on the fuel rail, but the temperature must be monitored, and I'm not sure of how to avoid short circuit. Has anyone found a suitable isolated wire, or another isolation method?

_________________
Volvo 945 LTT -96 med Flexitune II sedan juni -08


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: fre 10-01-22 16:36 
Offline

Blev medlem: tis 08-08-19 15:54
Inlägg: 503
Ort: Umeå, Västerbotten
nä jag tror inte den är för varm. Man får endel värmeförluster och etanolen är inte i kontakt med elementet och bränslet i FR hinner bytas ut. Jag funderar på 2 st sånna element och sätta fast på FR som kallstartshjälp.

_________________
Saab 900 2.0t -97 E85 mappad+Steg 1
Volvo 850 Flextek


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: fre 10-01-22 16:45 
Offline

Blev medlem: mån 08-09-01 22:07
Inlägg: 300
Ort: Ukraine, Donetsk
those PTC elements much cheaper and have stabilising temperature 80±10ºC

i think i can find such elements with 120±10ºC temp.

Bild


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: lör 10-01-23 11:23 
Offline

Blev medlem: tor 06-12-28 03:38
Inlägg: 593
Ort: Frösön nyss uppflytt
askilje skrev:
nä jag tror inte den är för varm. Man får endel värmeförluster och etanolen är inte i kontakt med elementet och bränslet i FR hinner bytas ut. Jag funderar på 2 st sånna element och sätta fast på FR som kallstartshjälp.

På 900:an?

J.K Nilsson


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: lör 10-01-23 16:17 
Offline

Blev medlem: tis 08-08-19 15:54
Inlägg: 503
Ort: Umeå, Västerbotten
jaa 900an, tror du inte att det fungerar??

_________________
Saab 900 2.0t -97 E85 mappad+Steg 1
Volvo 850 Flextek


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: lör 10-01-23 18:00 
Offline

Blev medlem: tor 06-12-28 03:38
Inlägg: 593
Ort: Frösön nyss uppflytt
Enklare att tjuvkoppla värmeplattor. ;)

J.K Nilsson


Upp
 Profil  
 
 Inläggsrubrik:
InläggPostat: lör 10-01-23 18:15 
Offline

Blev medlem: tis 08-08-19 15:54
Inlägg: 503
Ort: Umeå, Västerbotten
jodå, det har jag försökt :) jag kopplade 12v + till alla fyra kablarna. jag tyckte inte det fungerade så bra. Och sen hittade jag ingen brytare som höll för så starka strömmar som det handlade om.

_________________
Saab 900 2.0t -97 E85 mappad+Steg 1
Volvo 850 Flextek


Upp
 Profil  
 
Visa inlägg nyare än:  Sortera efter  
Ny tråd Svara på tråd  [ 62 inlägg ]  Gå till sida Föregående  1, 2, 3, 4, 5  Nästa

Alla tidsangivelser är UTC + 1 timme


Vilka är online

Användare som besöker denna kategori: Inga registrerade användare och 6 gäster


Du kan inte skapa nya trådar i denna kategori
Du kan inte svara på trådar i denna kategori
Du kan inte redigera dina inlägg i denna kategori
Du kan inte ta bort dina inlägg i denna kategori
Du kan inte bifoga filer i denna kategori

Sök efter:
Hoppa till:  
cron
POWERED_BY
Swedish translation by Peetra & phpBB Sweden © 2006-2011